This page refers to an older version of the product.
View the current version of the User Guide.

Configuring Host Profiles

A host profile defines the settings that the Velocity Client should use when it attempts to initiate a connection with a specific host. The host profile may include the emulation type, IP address of the host, or other settings. You may configure an unlimited number of host profiles from the device or through Wavelink Avalanche. Only one host profile is allowed per project using Velocity Console.

When a device user attempts to initiate a session with a host, the Velocity Client displays a list of available host profiles. The user selects the host he wants to connect to, and the Velocity Client uses the host profile settings to connect to the host.

Depending on the emulation type, different options are available when configuring a host profile. Likewise, some settings may not be present on the Velocity Client. To view the settings available from Android devices, see the Velocity Client User Guide. The following options are available when you configure a host profile in Velocity Console:

Profile Name	The name of the host profile.
Address	The IP address or host name of the host system to which the mobile device will connect.
Port	The TCP port number on which the host system is listening for emulation requests from Clients. By default, the port is set to 23. When Use SSH or Use SSH Tunnel is selected, the default port is changed to 22.
Emulation Type	The emulation type that the mobile device uses when connected to the host system.
VT Answer Back	Displays a string on the Smart device when it receives an ENQ from the host. It supports the following variables: • %m - %r representing the six octets of the MAC address. For example, use `%m%n%o%p%q%r` to contain the full MAC address as a response to an ENQ. • %a - %d representing the four octets of the IP address. • %s representing the session number. • %t representing the terminal ID (Avalanche only). • \## representing a hex character value This option is only available to VT emulation types.
Workstation ID	An ID for mobile devices connecting to an IBM host. The ID may include static characters and the following switches, which are used to capture dynamic data specific to each mobile device. It supports the following variables: • %a - %d. Captures specific octets of the IP address of the mobile device. For example, use %a%b%c%d to capture all four IP octets of the address of the mobile device, or use %d to capture only the last octet of the IP address of the mobile device. • %m - %r. Captures specific octets of the MAC address of the mobile device. For example, use %p%q%r to capture the last three octets of the MAC address of the mobile device. • %s. Captures the session number. A workstation ID can be 1-20 alphanumeric characters plus switches, but IBM hosts usually truncate workstation IDs that are more than 10 characters. The workstation ID should not begin with a numeric character. This option is only available to IBM emulation types.
Retry Workstation ID	Allows the Velocity Client to retry the workstation ID with a letter appended to it.
Default Safe Mode	Determines if the Velocity Client will automatically display screens in Safe Mode when a user connects to this host profile. If this option is not selected, devices will automatically display with Safe Mode disabled when a user connects.
Disable Predictive Formatting	Disables all predictive screens so that they do not appear on the Velocity Client. Any screen labeled as "Predictive" on the Screens tab cannot be used on the Client. Only screens that have been edited and are labeled as "Template" are usable at the device level. For more information about predictive versus template screens, see Editing Screen Elements. Predictive formatting should only be disabled if you have made manual changes to each screen. If a screen is unedited and displays as "Predictive" from the Screens tab, then the screen will not load at the device level and only displays a wait screen. No inputs are allowed on these screens.
Auto Carriage Return	Automatically applies the Enter or Send function after a menu option is selected from the Velocity Client.
Hardware Back Button Key	The HEX code value for a back button key on a menu. You can specify multiple back buttons for a host profile, separated by a comma. If left blank, the Back button on a device will do nothing.
Menu Up Key	The HEX code value for a menu up key. On the device toolbar, this appears to the left or right of the keyboard button. When the button is pushed, the defined key code is sent to the host. If left empty, this button does not appear when a menu is displayed.
Menu Down Key	The HEX code value for a menu down key. On the device toolbar, this appears to the left or right of the keyboard button. When the button is pushed, the defined key code is sent to the host. If left empty, this button does not appear when a menu is displayed.
Screen Rotation	Specifies which screen orientations are supported on the device. Possible values include: • Lock Portrait • Lock Landscape • Dynamic

Autologin

	Prompts	Responses
Name	The user name prompt that the host system uses. To prompt a user for a specific user name, you can use a variable delineated by a %. For example: %Gun Number% The text included within the % indicators is the information that appears in the prompt on the device. In the above example, the prompt would ask the user for "Gun Number" as their user name.	The response that the mobile device should send to the login prompt. Possible Values: 0 - 60 alpha-numeric characters.
Password	The password prompt that the host system uses. To accept a variable value, you can use a value delineated by a % after enabling the Use prompt scheme when editing the host profile in Velocity or through the Velocity Console. For example: %Store Number% In the above example, the prompt on the device would ask the user for a "Store Number" as their password.	The password that the mobile device should send to the host system at the password prompt. Possible Values: 0 - 60 alpha-numeric characters.
Command	The command prompt that the host system sends to the Velocity Client after the login is complete.	The command that the mobile device should send the host system at the command prompt. Possible Values: 0 - 60 alpha-numeric characters.

Authorization

License Server Address

The IP address or host name of the licensing server. If the devices are on the same local network as the licensing server, the address does not need to be specified as the Client will actively broadcast and find the server.

License Server Port

The TCP port number on which the License Server is listening for license requests from Clients. By default, the port is set to 1820. This field cannot be set until a License Server Address is specified.

License Server Site ID

The site ID associated with the License Server. This field cannot be set until a License Server Address is specified.

Site IDs are set as part of the License Server's initial setup. For more information, see the Terminal Emulation License Server Reference Guide on the Wavelink Web site.

SSH Settings

Use SSH	Uses SSH to encrypt the information sent to the host. There is no additional software for SSH on the device, but the host must be configured for SSH. When this option is selected, the Auto Login User and Auto Login Password fields appear and must be filled out and the Port field is changed to 22. This setting requires a public key to authenticate against the SSH server. The public key can only be associated with a host profile from the Velocity Console application. You can only select this option or Use SSH Tunnel, but not both.
Use SSH Tunnel	Sets whether or not to use SSH tunneling. If you are using 5250 emulation with SSH, you must use SSH tunneling. When this option is selected, the Auto Login User, Auto Login Password, Tunnel Address, and Tunnel Port fields appear below and the Port field is changed to 22. This setting requires a public key to authenticate against the SSH server. The public key can only be associated with a host profile from the Velocity Console application. You can only select this option or Use SSH, but not both.
Auto Login User	The username for accessing the SSH server. This option is only available when Use SSH or Use SSH Tunnel is selected.
Auto Login Password	The password associated with the SSH username. This option is only available when Use SSH or Use SSH Tunnel is selected.
Tunnel Address	The IP address or host name for the SSH tunnel. This option is only available when Use SSH Tunnel is selected.
Tunnel Port	The TCP port number associated with the Tunnel Address for SSH tunneling. This option is only available when Use SSH Tunnel is selected.

SSL Settings

Use SSL

Uses SSL to encrypt the information sent to the host. There is no additional software for SSH on the device, but the host must be configured for SSL. When this option is selected, the Port field is changed to 992.

This option cannot be enabled if Only Use ConnectPro connections is selected.

ConnectPro Settings

Only Use ConnectPro connections	Indicates whether the Velocity Client should only connect to the host through a ConnectPro server. If you enable this checkbox, you cannot select the Use SSL setting in the SSL Settings section.
Server Type	The version number of the ConnectPro server.
Address	The IP address or host name of the server. To prompt a device user for all or part of the address, use a variable delineated by %. Variables can be used in DNS names or IP addresses. For example: 192.168.42.%Store Number% The text that is inside the % indicators is the information that appears in the prompt on the device. In the above example, the prompt on the device would ask the user for "Store Number." If the user provides the store number 123, the Client attempts to connect to 192.168.42.123.
Port	The TCP port number on which the proxy server is listening for emulation requests from clients.
Terminate ConnectPro Session	Indicates when the ConnectPro server should terminate the connection to the host. Possible values include: • Never. The proxy server never terminates the session established with the host. The Client is responsible for manually terminating the session. • OnNetworkError. The proxy server terminates the session with the host when a network error occurs, such as a loss of network connectivity. • OnSessionExit. The proxy server terminates the session with the host when the session is terminated by the Velocity Client. By default, this option is selected. • Always. The proxy server will terminate the session with the host on a network error or when the session is terminated.
Client Reconnects if Unexpectedly Disconnected	Specifies if the Velocity Client will attempt to reconnect if the session with the proxy server is lost and the Client has not received a disconnect message from the proxy server. By default, this is set to Yes.
Reconnect String	Specifies the reconnect string that the Smart device should use when connecting to the host. Alternately, you may configure reconnect strings in ConnectPro.
Use SSL	Uses SSL/TLS to encrypt the information sent to the host. There is no additional software for SSL/TLS on Smart devices, but the host must be configured for SSL/TLS.
Use Custom Encryption	Uses a Wavelink custom encryption method to encrypt the connection to the ConnectPro server. When you use custom encryption, provide an encryption key in the Key field below.
Key	Specifies a custom encryption key.

Scanner Settings

VT Scan Terminator	Append termination characters to the end of scanned data. You can only set one character at a time. The following options are available: • \0D: ENTER • \09: TAB • [blank]: Leaving this field blank appends no character values to the end of the scanned data If you configure this field with a value and set Data Capture to Off, then you must configure the Intent section of the local DataWedge profile to be used with the Velocity Client. This setting is only available to VT emulation types.
Data Capture	Enables the ability for Smart devices to scan barcodes. Once set to Yes, the Barcode/MSR, Basic Data Formatting, Decoder Settings, Reader Settings, Scan Settings, and UPC/EAN Settings tabs appear below.
Barcode and MSR	• Enable/Disable Barcode Symbology. Configures which barcode decoders are enabled or disabled. We recommend disabling unnecessary decoders to improve device performance. • Enable Magnetic Stripe Reader. Enables the device's magnetic stripe reader.
Basic data formatting	• Enable. Enables or disables to use of basic data formatting settings. This is enabled by default. • Prefix to data. Adds characters to the beginning of the scanned data sent. • Suffix to data. Adds characters to the end of the scanned data sent. • Send data. Transfers captured data to the foreground application. This is enabled by default. Disabling the option prevents actual data from being transmitted, though prefix and suffix strings are still transmitted. • Send as hex. Sends the scanned data in hexadecimal format.
Decoder Settings	Codabar • CLSI Editing. Removes the start and stop characters and inserts a space after the first, fifth, and tenth characters on a 13-character Codabar symbol. • Lower limit of length range. Sets the lower limit for decoding Codabar symbols with a specific length range. For example, to decode Codabar symbols with between 8 and 24 characters, set this value to eight. By default, this is set to 6. • Upper limit of length range. Sets the upper limit for decoding Codabar symbols with a specific length range. For example, to decode Codabar symbols with between 8 and 24 characters, set this value to 24. By default, this is set to 55. • NOTIS Editing. Removes the start and stop characters from a Codabar symbol. • Redundancy. Forces the device to read the barcode twice before accepting data. Code 11 • Lower limit of length range. Sets the lower limit for decoding Code 11 symbols with a specific length range. For example, to decode Code 11 symbols with between 4 and 12 characters, set this value to four. By default, this is set to 4. • Upper limit of length range. Sets the upper limit for decoding Code 11 symbols with a specific length range. For example, to decode Code 11 symbols with between 4 and 12 characters, set this value to 12. By default, this is set to 55. • Redundancy. Forces the device to read the barcode twice before accepting data. • Report Check Digit. Transmits Code 11 data with a check digit. • Verify Check Digit. Checks all Code 11 symbols to verify that scanned data complies with the selected check digit algorithm. You can pick No Check Digit, 1 Check Digit, or 2 Check Digits. Code 128 • Check ISBT Table. Checks for ISBT barcodes against a table of commonly used in pairs. If ISTB 128 Concatenation Mode is enabled, selecting this option will concatenate only those pairs found in the table. • Enable GS1-128. Enables the use of GS1-128 subtypes. • Enable Plain Code 128. Enables the use of other non-EAN or ISBT Code 128 subtypes. • Enable ISBT 128. Enables the use of ISBT128 subtypes. • Lower limit of length range. Sets the lower limit for decoding Code 128 symbols with a specific length range. For example, to decode Code 128 symbols with between 8 and 24 characters, set this value to eight. By default, this is set to 0. • Upper limit of length range. Sets the upper limit for decoding Code 128 symbols with a specific length range. For example, to decode Code 128 symbols with between 8 and 24 characters, set this value to 24. By default, this is set to 55. • ISBT 128 Concatenation Mode. Decodes and concatenates pairs of ISBT codes when found. If a single ISBT symbol is present, the device decodes the symbol the number of times set with the Redundancy option before transmitting data. If not selected, the device won't concatenate pairs of ISBT codes when found. • Redundancy. Forces the device to read the barcode twice before accepting data. If Check ISBT Table is selected, this option is checked and cannot be edited. • Security Level. Uses a level of decode security for Code 128 barcodes. Higher levels of security are used to reduce misdecodes at the cost of barcode quality. You can pick between Security Level 0, Security Level 1, Security Level 2, and Security Level 3. Code 39 • Convert Code 39 to Code 32. Enables scanning a barcode to enable or disable the use of the Code 32 variant. • Full ASCII. Enables the use of a Code 39 variant that pairs characters to encode to the full ASCII character set. • Lower limit of length range. Sets the lower limit for decoding Code 39 symbols with a specific length range. For example, to decode Code 39 symbols with between 8 and 24 characters, set this value to eight. By default, this is set to 0. • Upper limit of length range. Sets the upper limit for decoding Code 39 symbols with a specific length range. For example, to decode Code 39 symbols with between 8 and 24 characters, set this value to 24. By default, this is set to 55. • Redundancy. Forces the device to read the barcode twice before accepting data. • Report Check Digit. Transmits Code 39 data with a check digit. • Report Code 32 Prefix. Enables scanning a barcode to enable or disable adding the prefix character "A" to all Code 32 barcodes. • Verify Check Digit. Checks all Code 39 symbols to verify that scanned data complies with the selected check digit algorithm. Enable this feature only if the Code 39 symbols contain a modulo 43 check digit. • Security Level. Uses a level of decode security for Code 39 barcodes. Higher levels of security are used to reduce misdecodes at the cost of barcode quality. You can pick between Security Level 0, Security Level 1, Security Level 2, and Security Level 3. Code 93 • Lower limit of length range. Sets the lower limit for decoding Code 93 symbols with a specific length range. For example, to decode Code 93 symbols with between 4 and 12 characters, set this value to four. By default, this is set to 0 . • Upper limit of length range. Sets the upper limit for decoding Code 93 symbols with a specific length range. For example, to decode Code 93 symbols with between 4 and 12 characters, set this value to 12. By default, this is set to 55. • Redundancy. Forces the device to read the barcode twice before accepting data. Composite AB • UCC Link Mode. Enables UCC Link Mode. You can pick Auto Discriminate, Link Flag Ignored, or Always Linked. Discrete 2 of 5 • Lower limit of length range. Sets the lower limit for decoding a Discrete 2 of 5 symbol with a specific length range. For example, to decode a Discrete 2 of 5 symbol with between 4 and 12 characters, set this value to four. By default, this is set to 0 . • Upper limit of length range. Sets the upper limit for decoding a Discrete 2 of 5 symbol with a specific length range. For example, to decode a Discrete 2 of 5 symbol with between 4 and 12 characters, set this value to 12. By default, this is set to 14. • Redundancy. Forces the device to read the barcode twice before accepting data. Interleaved 2 of 5 • Check Digit. Defines the use of check digits in Interleaved 2 of 5 symbols. The following options are available for selection: • No Check Digit. A check digit is not used. • USS Check Digit. Checks the integrity of all Interleaved 2 of 5 symbols to ensure compliance with the Uniform Symbology Specification (USS) check digit algorithm. • OPCC Check Digit. Checks the integrity of all Interleaved 2 of 5 symbols to ensure compliance with the Optical Product Code Council (OPCC) check digit algorithm. • Convert ITF-14 to EAN 13. Converts 14-character Interleaved 2 of 5 barcodes to EAN-13 and then transmits them as EAN-13. To use this option, Interleaved 2 of 5 barcodes must be enabled and have a leading zero before a valid EAN-13 check digit. • Lower limit of length range. Sets the lower limit for decoding an Interleaved 2 of 5 symbol with a specific length range. For example, to decode an Interleaved 2 of 5 symbol with between 4 and 12 characters, set this value to four. By default, this is set to 10. • Upper limit of length range. Sets the upper limit for decoding an Interleaved 2 of 5 symbol with a specific length range. For example, to decode an Interleaved 2 of 5 symbol with between 4 and 12 characters, set this value to 12. By default, this is set to 14. • Redundancy. Forces the device to read the barcode twice before accepting data. • Report Check Digit. Transmits Interleaved 2 of 5 data with a check digit. • Security Level. Uses a level of decode security for Interleaved 2 of 5 barcodes. Higher levels of security are used to reduce misdecodes at the cost of barcode quality. You can pick between Security Level 0, Security Level 1, Security Level 2, and Security Level 3. Matrix 2 of 5 • Lower limit of length range. Sets the lower limit for decoding a Matrix 2 of 5 symbol with a specific length range. For example, to decode a Matrix 2 of 5 symbol with between 4 and 8 characters, set this value to four. By default, this is set to 0. • Upper limit of length range. Sets the upper limit for decoding a Matrix 2 of 5 symbol with a specific length range. For example, to decode a Matrix 2 of 5 symbol with between 4 and 8 characters, set this value to eight. By default, this is set to 10. • Redundancy. Forces the device to read the barcode twice before accepting data. • Report Check Digit. Transmits Matrix 2 of 5 data with a check digit. • Verify Check Digit. Checks all Matrix 2 of 5 symbols to verify that scanned data complies with the selected check digit algorithm. MSI • Check Digit. Checks all MSI symbols to verify that scanned data complies with the selected check digit algorithm. You can pick between One Check Digit or Two Check Digit. • Check Digit Scheme. Selects the algorithm used to verify the second MSI check digit. You can pick between Mod-11-10 or Mod-10-10. • Lower limit of length range. Sets the lower limit for decoding an MSI symbol with a specific length range. For example, to decode an MSI symbol with between 4 and 12 characters, set this value to four. By default, this is set to 4. • Upper limit of length range. Sets the upper limit for decoding an MSI symbol with a specific length range. For example, to decode an MSI symbol with between 4 and 12 characters, set this value to 12. By default, this is set to 55. • Redundancy. Forces the device to read the barcode twice before accepting data. • Report Check Digit. Transmits MSI data with the check digits. UK Postal • Report Check Digit. Transmits UK Postal data with the check digits. UPC-A • Preamble. Transmits a UPC-A preamble as part of the UPC symbol. This consists of Country Code and System Character and can be set to one of the following options: • Preamble None. Transmit no preamble. • Preamble Sys Char. Transmit System Character only. • Preamble Country and Sys Char. Transmit Country Code and System Character. • Report Check Digit. Transmits UPCA data with a check digit. UPC-E0 • Convert UPC-E0 to UPC-A. Converts UPC-E0 decoded data to UPC-A format prior to transmission. • Preamble. Transmits a UPC-E0 preamble as part of the UPC symbol. This consists of Country Code and System Character and can be set to one of the following options: • Preamble None. Transmit no preamble. • Preamble Sys Char. Transmit System Character only. • Preamble Country and Sys Char. Transmit Country Code and System Character. • Report Check Digit. Transmits UPC-E0 data with a check digit. UPC-E1 • Convert UPC-E1 to UPC-A. Converts UPC-E1 decoded data to UPC-A format prior to transmission. • Preamble. Transmits a UPC-E1 preamble as part of the UPC symbol. This consists of Country Code and System Character and can be set to one of the following options: • Preamble None. Transmit no preamble. • Preamble Sys Char. Transmit System Character only. • Preamble Country and Sys Char. Transmit Country Code and System Character. • Report Check Digit. Transmits UPC-E1 data with a check digit.
Reader Settings	• Beam Timer. Sets the maximum amount of time the reader will remain on. If set to 0, the reader will stay on indefinitely. This can be set between 0 and 60,000 milliseconds in increments of 100 milliseconds. By default, this is set to 15,000 milliseconds. • Illumination Mode. Turns illumination on. • Inverse 1D Mode. Allows the decoding of 1D barcodes. The following options are available for selection: • Disabled. Disables the decoding of inverse 1D symbols. • Enabled. Enables the decoding of only inverse 1D symbols. • Auto. Enables the decoding of both positive and inverse 1D symbols. • LCD Mode. Allows the device to read barcodes from LCD displays, such as Smart phones. • Linear Security Level. Sets the number of times a barcode is read to confirm accurate decoding. • Security All Twice. All barcodes are read twice for redundancy. • Security Short or Codabar. If a barcode is short or Codabar, it is read twice for redundancy. • Security Long and Short. All long barcodes are read twice and all short barcodes are read three times for redundancy. • Security All Thrice. All barcodes are read three times for redundancy. • Low Power Timeout. Sets the interval for how long a device should remain inactive before running in low-power mode. This interval is measured in milliseconds. • Picklist. Allows the device to only decode the barcode located directly under the cross-hair part of the pattern. This is used when multiple barcodes appear in the field of view when decoding and only one is targeted for decoding. The following options are available for selection: • Disabled. Disables Picklist mode, and any barcode within the field of view will be decoded. • Enabled (Reticle). Enables Picklist mode so that the barcode directly under the cross-hair is decoded. • Centered. Enables Picklist mode so that only the barcode located at the center of the image is decoded. This mode is only usable by decoder modules that support viewfinders. • ViewFinder Mode. Displays viewfinder modes for targeted scanning. The following options are available for selection: • Static Reticle. Enables the viewfinder as well as a red reticle in the center of the screen to assist with selecting a barcode. • ViewFinder Disabled. Disables the viewfinder. • ViewFinder Enabled. Enables only the viewfinder.
Scan Settings	• Code ID Type. Determines the code ID character used to define the code type of a scanned barcode. This option is recommended when decoding more than one code type. The following options are available for selection: • None. No prefix is used. • AIM. A standards-based three character prefix. • Symbol. A symbol-defined single character prefix. • Data Capture LED ID. Sets the Data Capture LED ID. This is set to 8 by default. • Decode Audio Feedback. Sets an audio tone to sound upon a good decode. • Decode Feedback LED Timer. Sets how long the audio tone plays in milliseconds upon a good decode. This is set to 75 by default. • Decode Haptic Feedback. Enables the device to vibrate upon a good decode. • Decoding LED Notification. Enables the device to blink the LED notification light upon a good decode. • Scanner. Sets supported scanner device types. You can pick Internal Camera, Internal Imager, or Internal Laser.
UPC/EAN Settings	• Bookland. Enables the decoding of Bookland data. • Bookland Format. Specifies a format for Bookland data decoded. The following options are available for selection: • ISBN-10. The scanner reports Bookland data (starting with 978) in the 10-digit format with a check digit to ensure backward compatibility. • ISBN-13. The scanner reports Bookland data (starting with either 978 or 979) as EAN-13 in the appropriate format. • Convert DataBar To UPC EAN. Converts DataBar barcodes to UPC/EAN format. To use this setting, UPC/EAN symbologies must be enabled on the Barcode/MSR tab. • Coupon. Enables coupon code decoding. To ensure devices are able to successfully decode coupon codes, all of the required decoders must be enabled. • Coupon Report Mode. Sets the supported coupon modes that a scanner can decode. The following options are available for selection: • Old Coupon Report Mode. The scanner will decode only the old coupon format. • New Coupon Report Mode. The scanner will decode only the new GS1 DataBar coupon format. • Both Coupon Report Mode. The scanner will decode both the old coupon format as well as the new GS1 DataBar coupon format. • Linear Decode. Enables linear decoding. • Random Weight Check Digit. Enables random weight check digit verifications. • Retry Count. Sets a retry count for auto-discriminating supplementals. Possible values are between 2 and 20. This field is only valid if Supplemental Mode is set to Supplementals Auto, Supplementals Smart, Supplementals 378-379, Supplementals 978-979, Supplementals 977, or Supplementals 414-419-434-439. • Security Level. Uses a level of decode security for UPC/EAN barcodes. Higher levels of security are used to reduce misdecodes at the cost of barcode quality. You can pick between Security Level 0, Security Level 1, Security Level 2, and Security Level 3. • Supplemental 2. Enables the decoding of Supplemental 2 data. • Supplemental 5. Enables the decoding of Supplemental 5 data. • Supplemental Mode. Enables the decoding of supplemental symbols and specific UPC/EAN codes. The following options are available for selection: • No Supplementals. The scanner is presented with a UPC/EAN and supplemental symbol, but the scanner only decodes the UPC/EAN characters. • Always. The scanner decodes only UPC/EAN symbols containing supplemental characters. • Auto. The scanner decodes UPC/EAN symbols with and without supplemental characters. • Smart. Enables smart supplementals. The decoder returns decoded values of the main block if they don't belong to one of the following supplemental types: 378, 379, 977, 978, 979, 414, 419, 434, or 439. • Supplemental 378-379. Enables auto-discriminate supplemental for UPC/EAN codes starting with 378 or 379. Any other barcodes not starting with these digits are ignored. • Supplemental 978-979. Enables auto-discriminate supplemental for UPC/EAN codes starting with 978 or 979. Any other barcodes not starting with these digits are ignored. • Supplemental 414-419-434-439. Enables auto-discriminate supplemental for UPC/EAN codes starting with 414, 419, 434, or 439. Any other barcodes not starting with these digits are ignored. • Supplemental 977. Enables auto-discriminate supplemental for UPC/EAN codes starting with 977. Any other barcodes not starting with this digit are ignored.

To associate a host profile with your project:

1 Click the Hosts button.

2 Configure the host profile as needed.

3 To save your changes, click the Save button or navigate to another screen within Velocity Console.

When your project is deployed and added to a mobile or Smart device, the new host profile settings are added to the Velocity Client. Replacing the details for an old host profile from the project level will not delete any host profiles created from previous deployments. For more information about deploying a project, see Deploying Projects.

This page refers to an older version of the product.
View the current version of the User Guide.

The topic was:

Inaccurate

Incomplete

Not what I expected

Other

Privacy and Legal